What is OBD-II Code P0798 – Pressure Control Solenoid C Electrical



What is OBD-II Code P0798 – Pressure Control Solenoid C Electrical

When your check engine light comes on, it can be a cause for concern. It could indicate a potentially serious issue or something relatively simple. However, having an OBD-II code reader can help you identify the specific issue, which can then be addressed appropriately. One of the codes you may come across is P0798 – Pressure Control Solenoid C Electrical. In this article, we’ll take a closer look at what this code means and how to repair the issue.

What does OBD-II Code P0798 mean?

An OBD-II code P0798 refers to a problem with the transmission pressure control solenoid C electrical circuit. The pressure control solenoids are the components responsible for controlling the pressure within the transmission. Solenoids are essentially electromagnets that allow for the flow of fluid through the valve body. Each solenoid is responsible for regulating the fluid pressure to a specific clutch pack, which then engages a specific gear in the transmission. Solenoids can either be on/off type or proportional, with the latter being the more advanced of the two.

The exact nature of the issue can vary depending on the make and model of your vehicle, as well as the severity of the problem. However, some potential causes of the P0798 code include a faulty solenoid control circuit, a malfunctioning pressure control solenoid, or a bad transmission control module (TCM). In certain cases, this issue can be caused by a broken wire, a bad connection, or a blown fuse.

Symptoms of P0798 Code

There are several symptoms that can indicate a problem with the pressure control solenoid C electrical circuit. The most common signs that you may notice include:

1. Check engine light: The most obvious sign you have a problem with your transmission pressure control solenoid C electrical circuit is when your check engine light comes on. This could be a sign of various issues, but by reading the OBD-II code, you can narrow down the problem to this specific part of the transmission.

2. Transmission slipping or shifting harshly: Another common symptom is the transmission slipping or shifting erratically. This is because the pressure control solenoid regulates the pressure to the clutch packs that engage the gears. If the solenoid is not functioning properly, it can cause the transmission to slip or shift harshly.

3. Transmission won’t shift: If the pressure control solenoid C is completely failed, your car may not be able to shift gears at all. This can be a potentially dangerous situation if you are driving at highway speeds.

How to Repair the P0798 Code

If you have determined that the issue is with the pressure control solenoid C electrical circuit, there are several steps you can take to repair the problem. However, before you begin any repairs, it’s important to have your vehicle diagnosed by a reputable mechanic.

1. Inspect the electrical connections: Start by inspecting the electrical connections to the pressure control solenoid C. Make sure that all wires leading to the solenoid are connected properly and that there is no physical damage to the wiring.

2. Replace the pressure control solenoid: If your inspection reveals that there are no problems with the wiring, you may need to replace the pressure control solenoid. This part can wear out over time, especially if you frequently drive in stop-and-go traffic or under heavy loads.

3. Replace the transmission control module: If the solenoid is functioning correctly, the most likely culprit is a faulty transmission control module. This part is responsible for sending the signal to the pressure control solenoid to engage and disengage, and if it’s malfunctioning, it can cause the solenoid to fail.

FAQs

1. Can I still drive my car if I have an OBD-II code P0798?

It’s always better to be safe than sorry, so we recommend not driving your car until the issue has been resolved. While you may be able to drive your car with the P0798 code present, it can cause further damage to your transmission and ultimately become a more expensive problem to repair.

2. How much does it cost to repair an OBD-II code P0798?

The cost of repairing an OBD-II code P0798 can vary depending on the make and model of your vehicle and the severity of the problem. However, you can expect to spend anywhere from $200 to $1,000 on parts and labor.

3. Can I fix an OBD-II code P0798 myself?

If you have experience working on cars and the necessary tools, you may be able to fix an OBD-II code P0798 yourself. However, if you are not confident in your abilities, it’s always best to bring your vehicle to a reputable mechanic.

4. How long does it take to repair an OBD-II code P0798?

The time it takes to repair an OBD-II code P0798 can vary depending on the type of repair that’s needed. In some cases, it could take as little as an hour, while more complicated repairs could take several days.

5. Can I prevent an OBD-II code P0798?

Some causes of an OBD-II code P0798 are out of your control, such as a faulty transmission control module. However, taking care of your vehicle through regular maintenance can help prevent issues with the transmission pressure control solenoid C electrical circuit. This includes keeping your transmission fluid clean and topped off and having your transmission serviced regularly.

Conclusion

The OBD-II code P0798 is a relatively common transmission issue that can cause a number of symptoms, including slipping and shifting problems, as well as a check engine light. While the exact nature of the issue can vary depending on your vehicle, the most common causes include a faulty solenoid control circuit, a bad pressure control solenoid C, or a malfunctioning transmission control module. If you suspect you have an issue with your transmission, it’s always best to bring your vehicle to a reputable mechanic. They can diagnose the problem and recommend the best course of action to get you back on the road safely.

Scroll to Top